久久成人在线观看_91视频首页_国产成人免费视频_国产成人一区_久久久久国产一区二区_国产一区二区三区在线免费

What should be paid attention to when grinding the crankshaft of natural gas generator sets?

Release time:2023-03-02 Publisher:ZHONGTUO
The smooth grinding of the crankshaft of natural gas generator set is one of the key processes to ensure the repair quality. When the outer circle surface of the timing gear journal and the flywheel flange is used as the basis for smooth grinding, the curvature must be corrected before grinding, and the runout of the intermediate main journal before grinding shall not be greater than 0.3 mm. If the bending is not corrected in advance, after weaving, the crankshaft will produce a new axis that intersects with the original flywheel flange and the axis of the timing gear, which changes the turning radius, destroys the dynamic balance force, shortens the service life, and intensifies the wear of relevant parts. The noise of the timing gear is also loud, and the rear oil seal leaks, which increases the unbalanced rotating quality of the engine.

煤化工尾氣發電機組
It is one of the key issues of repair quality to strictly ensure that the size of the fillet radius of the crankshaft journal of the natural gas generator set meets the drawing requirements. However, the general car repair shop does not pay enough attention to this. The grinding wheel is rarely polished, and the radius of the polished fillet is often smaller than the specified size. According to statistics, the fillet radius is less than 2.5 mm, and its fatigue strength is only less than 80% of that of 2.5 mm. Since the grinding wheel for smooth grinding of crankshaft is often trimmed with the grinding wheel fillet corrector attached to the grinding machine, so that the size of the grinding fillet meets the requirements, there has been no broken shaft since the vibration surfacing was put into production.
 
During the operation of natural gas generator set, due to the complex stress and working conditions of the crankshaft, the sliding speed of each friction surface is very high, and the heat dissipation condition is poor. Therefore, the main journal and connecting rod journal of the crankshaft will inevitably wear during the operation, and the wear is uneven. The main performance is that the journal has roundness, cylindricity exceeds the standard value and strain. The most worn part of the connecting rod journal is generally on the inner side of each journal, that is, on the side of the crankshaft centerline, so that the journal is out of round; The parts that wear into a cone are generally on the side where the impurities in the lubricating oil channel attach and the parts with large stress. Crankshaft main journal_ The wear parts of the engine vary according to the degree of strengthening of the engine, the number of cylinders, the length of the crankshaft and the counterweight of the balance weight, and the wear is more uniform than that of the connecting rod journal. Practice shows that the wear of connecting rod journal is faster than that of main journal, but the wear of main journal is more serious than that of connecting rod journal.
 
Inspection and treatment methods of natural gas generator set. Find out the worn part according to the wear rule of each journal, and measure its roundness and cylindricity with an outside micrometer to determine the repair level and grinding size of the crankshaft.
 
The smooth grinding of crankshaft is one of the key processes to ensure the repair quality. When the outer circle surface of the timing gear journal and the flywheel flange is used as the basis for smooth grinding, the curvature must be corrected before grinding, and the runout of the intermediate main journal before grinding shall not be greater than 0.3 mm. If the bending is not corrected in advance, after weaving, the crankshaft will produce a new axis that intersects with the original flywheel flange and the axis of the timing gear, which changes the turning radius, destroys the dynamic balance force, shortens the service life, and intensifies the wear of relevant parts. The noise of the timing gear is also loud, and the rear oil seal leaks, which increases the unbalanced rotating quality of the engine.
 
It is one of the key issues of repair quality to strictly ensure that the size of the crankshaft journal fillet radius meets the drawing requirements. However, the general car repair shop does not pay enough attention to this. The grinding wheel is rarely polished, and the radius of the polished fillet is often smaller than the specified size. According to statistics, the fillet radius is less than 2.5 mm, and its fatigue strength is only less than 80% of that of 2.5 mm. Since the grinding wheel for smooth grinding of crankshaft is often trimmed with the grinding wheel fillet corrector attached to the grinding machine, so that the size of the grinding fillet meets the requirements, there has been no broken shaft since the vibration surfacing was put into production.

Service

classification

product

recommendation

Contact

Information
  • Tel:0531-69953988
    13012995645
  • Add:101, Building 5, Liandong U Valley Science and Technology Innovation Center, Zhangjin Comprehensive Bonded Zone, No. 33688 Jingshi East Road, Suncun Street, Jinan Area, China (Shandong) Pilot Free Trade Zone

截屏,微信識別二維碼

  • 主站蜘蛛池模板: 国内精品久久久久久不卡影院 | 日韩在线电影 | 欧美成 人版中文字幕 | 99热精品成人免费观看 | 精品深夜av无码一区二区老年 | 欧美特黄一级aa毛片 | 无码人妻丰满熟妇区五十路百度 | 国产成人ae在线观看网站站 | 欧美成亚洲 | 久久精品卫校国产小美女 | 免费大片黄在线观看日本 | 狠狠色狠狠色狠狠五月ady | 一本色道无码不卡在线观看 | 人妻人人做人做人人爱 | 久久久久国产一级毛片高清版 | 国产成人精品实拍在线 | 免费99视频有精品视频高清 | 亚洲国产一区二区a毛片日本 | 久久久久国产精品免费免费不卡 | 小香蕉影院| s级毛片 | 成人在线播放av | 亚洲精品久久婷婷丁香51 | 韩国美女人成网站在线看看 | 不卡中文字幕 | 亚洲中文无码永久免费 | 欧美丰满大乳高跟鞋 | 国产视频不卡在线 | 亚洲熟妇av一区二区三区宅男 | 国产视频第一页 | 欧美日韩国产综合在线 | 久操热| 色综合伊人色综合网亚洲欧洲 | 国产欧美日韩综合精品二区 | 最新亚洲精品 | 久久99亚洲精品久久久久 | 欧美精品videossex少妇 | 推川悠里在线 | 色拍自拍亚洲综合图区 | 久热在线这里只有精品 | 久久久噜噜噜久久老司机 |